Copyright (c) Hyperion Entertainment and contributors.
Revision 2 + 3
Contents
- 1 Authors
- 2 SANA-II Network Device Driver Specification
- 3 Driver Form
- 4 Opening a SANA-II Device
- 5 Buffer Management
- 6 Packet Type
- 7 Addressing
- 8 Hardware Type
- 9 Errors
- 10 Standard Commands
- 11 Driver Installation
- 12 Acknowledgments
- 13 Unresolved Issues
- 14 SANA-II network device driver Autodocs
- 14.1 sana2.device/AbortIO
- 14.2 sana2.device/CloseDevice
- 14.3 sana2.device/CMD_CLEAR
- 14.4 sana2.device/CMD_FLUSH
- 14.5 sana2.device/CMD_INVALID
- 14.6 sana2.device/CMD_READ
- 14.7 sana2.device/CMD_RESET
- 14.8 sana2.device/CMD_START
- 14.9 sana2.device/CMD_STOP
- 14.10 sana2.device/CMD_UPDATE
- 14.11 sana2.device/CMD_WRITE
- 14.12 sana2.device/OpenDevice
- 14.13 sana2.device/S2_ADDMULTICASTADDRESS
- 14.14 sana2.device/S2_BROADCAST
- 14.15 sana2.device/S2_CONFIGINTERFACE
- 14.16 sana2.device/S2_DELMULTICASTADDRESS
- 14.17 sana2.device/S2_DEVICEQUERY
- 14.18 sana2.device/S2_GETGLOBALSTATS
- 14.19 sana2.device/S2_GETSPECIALSTATS
- 14.20 sana2.device/S2_GETSTATIONADDRESS
- 14.21 sana2.device/S2_GETTYPESTATS
- 14.22 sana2.device/S2_MULTICAST
- 14.23 sana2.device/S2_OFFLINE
- 14.24 sana2.device/S2_ONEVENT
- 14.25 sana2.device/S2_ONLINE
- 14.26 sana2.device/S2_READORPHAN
- 14.27 sana2.device/S2_TRACKTYPE
- 14.28 sana2.device/S2_UNTRACKTYPE
- 15 Callback mechanism Autodocs
- 16 Ethernet description
- 17 ARCNET description
Authors
Copyright © 1992-2000 Amiga, Inc. All Rights Reserved
Amiga is a registered trademark of Amiga, Inc. Ethernet is a trademark of Xerox Corporation. ARCNET is a trademark of Datapoint Corporation. DECNet is a trademark of Digital Equipment Corporation. AppleTalk is a trademark of Apple Computer, Inc.
SANA-II Network Device Driver Specification
The "SANA-II Network Device Driver Specification" is a standard for an Amiga software interface between networking hardware and network protocol stacks (or for software tools such as network monitors). A network protocol stack is a layer of software that network applications use to address particular processes on remote machines and to send data reliably in spite of hardware errors. There are several common network protocol stacks including TCP/IP, OSI, AppleTalk, DECNet and Novell.
SANA-II device drivers are intended to allow multiple network protocol stacks running on the same machine to share one network device. For example, the TCP/IP and AppleTalk protocol stacks could both run on the same machine over one ethernet board. The device drivers are also intended to allow network protocol stacks to be written in a hardware-independent fashion so that a different version of each protocol stack doesn't have to be written for each networking hardware device.
The standard does not address the writing of network applications. Application writers must not use SANA-II Device Drivers directly. Network applications must use the API provided by the network protocol software the application supports. There is not an Amiga standard network API at the time of this writing, though there is the AS225 TCP/IP package and its socket.library as well as other (third-party) packages.
To write a SANA-II device driver, you will need to be familiar with the specification documents for the hardware you are writing to and with the "SANA-II Network Device Driver Specification".
To write a network protocol stack which will use SANA-II device drivers, you should have general familiarity with common network hardware and must be very familiar with the "SANA-II Network Device Driver Specification" as well as the specification for the protocol you are developing. If you are creating a new protocol, you must obtain a protocol type number for any hardware on which your protocol will be used.
Amiga supports the SANA-II specification by providing drivers for the Amiga network hardware. We have an A2065.device (Ethernet) and intend to produce an A2060.device (ARCNET). We also try to examine review copies of third-party SANA-II networking hardware and software to try to make sure that they interoperate with our products.
This standard has undergone several drafts with long periods for comment from developers and the Amiga community at large. These drafts include a UseNet release which was also distributed on the Fish Disks in June, 1991 (as well as published in the '91 DevCon notes), and the November 7 Draft for Final Comment and Approval distributed via Bix, ADSP and UseNet. There were also several intermediate drafts with more limited distribution.
This version of the specification is final. Any new version of the standard (i.e., to add new features) is planned to be backward compatible. No SANA-II device driver or software utilizing those drivers should be written to any earlier version of the specification.
Distribution of this version of the standard is unlimited. Anyone may write Amiga software which implements a SANA-II network device driver or which calls a SANA-II network device driver without restriction and may freely distribute such software that they have written.
It is important to try to test each SANA-II device driver against all software which uses SANA-II devices. Available example programs are valuable in initial testing. The Amiga Networking Group is interested in receiving evaluation and/or beta test copies of all Amiga networking hardware, SANA-II device drivers and software which uses SANA-II devices. However, we make no assurances regarding any testing which we may or may not perform with such evaluation copies.
Driver Form
SANA-II device drivers are Amiga Exec device drivers. They use an extended IORequest structure and a number of extended commands for tallying network statistics, sending broadcasts and multicasts, network addressing and the handling of unexpected packets. The SDK includes information on how to construct an Exec device.
Opening a SANA-II Device
As when opening any other Exec device, on the call to OpenDevice() a SANA-II device receives an IORequest structure which the device initializes for the opener's use. The opener must copy this structure if it desires to use multiple asynchronous requests. The SANA-II IORequest is defined as follows:
struct IOSana2Req { struct IORequest ios2_Req; ULONG ios2_WireError; ULONG ios2_PacketType; UBYTE ios2_SrcAddr[SANA2_MAX_ADDR_BYTES]; UBYTE ios2_DstAddr[SANA2_MAX_ADDR_BYTES]; ULONG ios2_DataLength; APTR ios2_Data; APTR ios2_StatData; APTR ios2_BufferManagement; };
- ios2_Req
- A standard Exec device IORequest.
- ios2_WireError
- A more specific device code which may be set when there is an io_Error. See <devices/sana2.h> for the defined WireErrors.
- ios2_PacketType
- The type of packet requested. See the section on "Packet Types".
- ios2_SrcAddr
- The device fills in this field with the interface (network hardware) address of the source of the packet that satisfied a read command. The bytes used to hold the address will be left justified but the bit layout is dependent on the particular type of network.
- ios2_DstAddr
- Before the device user sends a packet, it fills this with the interface destination address of the packet. On receives, the device fills this with the interface destination address. Other commands may use this field differently (see the "SANA-II network device driver Autodocs" in the SDK). The bytes used to hold the address will be left justified but the bit layout is dependent on the particular type of network.
- ios2_DataLength
- The device user initializes this field with the amount of data available in the Data buffer before passing the IOSana2Req to the device. The device fills in this field with the size of the packet data as it was sent on the wire. This does not include the header and trailer information. Depending on the network type and protocol type, the driver may have to calculate this value. This is generally used only for reads and writes (including broadcast and multicast).
- ios2_Data
- A pointer to some abstract data structure containing packet data. Drivers may not directly manipulate or examine anything pointed to by Data! This is generally used only for reads and writes (including broadcast and multicast).
- ios2_StatData
- Pointer to a structure in which to place a snapshot of device statistics. The data area must be long word aligned. This is only used on calls to the statistics commands.
- ios2_BufferManagement
- The opener places a pointer to a tag list in this field before calling OpenDevice(). Functions pointed to in the tag list are called by the device when processing IORequests from the opener. When returned from OpenDevice(), this field contains a pointer to driver-private information used to access these functions. See "Buffer Management" below for more details.
The flags used with the device on OpenDevice() are (SANA2OPB_xxx):
- SANA2OPB_MINE
- Exclusive access to the unit requested.
- SANA2OPB_PROM
- Promiscuous mode requested. Hardware which supports promiscuous mode allows all packets sent over the wire to be captured whether or not they are addressed to this node.
- Note: Promiscuous mode requires exclusive opening of the device.
The flags used during I/O requests are (SANA2IOB_xxx):
- SANA2IOB_RAW
- Raw packet read/write requested. Raw packets should include the entire data-link layer packet. Devices with the same hardware device number should have the same raw packet format.
- SANA2IOB_BCAST
- Broadcast packet (received).
- SANA2IOB_MCAST
- Multicast packet (received).
- SANA2IOB_QUICK
- Quick IO requested.
Buffer Management
Unlike most other Exec Device drivers, SANA-II drivers have no internal buffers. Instead, they read/write to/from an abstract data structure allocated by the driver user. The driver accesses these buffers only via functions that the driver user provides to the driver. The driver user must provide two functions: one copies data to the abstract data structure and one copies data from the abstract data structure. The driver user can therefore choose the data structure used for buffer management by both the driver and driver user in order to have efficient memory and CPU usage overall.
The IOSana2Req contains a pointer to data and the length of said data. A driver is not allowed to make assumptions about how the data is stored. The driver cannot directly manipulate or examine the buffer in any manner. The driver can only access the buffer by calling the functions provided by the driver user.
Before calling OpenDevice(), the driver user points ios2_BufferManagement to a list of tags (defined in <devices/sana2.h>) which include pointers to the buffer management functions required by the driver (defined below). The driver will fail to open if the driver user does not supply all of the required functions. If the device opens successfully, the driver sets ios2_BufferManagement to a value which this opener must use in all future calls to the driver. This "magic cookie" is used from then on to access these functions (a "magic cookie" is a value which one software entity passes to another but which is only meaningful to one of the software entities). The driver user may not use the "magic cookie" in any way--it is for the driver to do with as it wishes. The driver could in theory choose to just copy the tag list to driver-owned memory and then parse the list for every IORequest, but it is much more efficient for the driver to create some sort of table of functions and to point ios2_BufferManagement to that table.
Another recommendation for the ``magic cookie`` is to use it to maintain a separate packet read queue for each device opener. This would allow multiple protocol stacks that all wish to receive the same packet type to work together without having to "know" about each other as Envoy and AS225 do right now. What does multiple protocol stack support mean? Basically this means that each opener gets all the packets necessary. If a packet comes in that fills a request for more than one opener of the device, all of them will get a copy of the packet. This feature should never be left out of a device design. If it is missing, the usefulness of the device is severely limited.
The SLIP and A2065 driver now do this, so it would be possible (for example) to run Envoy, AS225 and the AmiTCP package together on the same hardware without conflicts.
In order to help system load, a new callback has been added to allow protocol stacks to reject packets that are known to not be useful. Envoy's nipc.library (for example) could be modified to reject TCP packets (as it never uses them).
The specification currently defines three tags for the OpenDevice() ios2_BufferManagement tag list:
- S2_CopyToBuff
- This is a pointer to a function which conforms to the CopyToBuff Autodoc (see page copytobuffpage).
- S2_CopyFromBuff
- This is a pointer to a function which conforms to the CopyFromBuff Autodoc (see page copyfrombuffpage).
- S2_PacketFilter
- [optional]
- This is a pointer to a standard Hook to be called before S2_CopyToBuff is done. See the PacketFilter Autodoc on page packetfilterpage for more information.
Packet filtering
What does packet filtering do? With the original "SANA-II Network Device Driver Specification", a protocol stack could open a device and ask for certain packet types. It got all the packets that matched this type. As it turned out, this could be mighty inefficient if there were packets that the protocol stack did not use at all. These would go into read processing of the protocol stack and waste CPU time even though they could have been easily identified on arrival.
Enhancements for better buffer management
It has been observed that the standard buffer management callbacks may not be very efficient for certain types of hardware. They also do not allow driver DMA access. Therefore the original "SANA-II Network Device Driver Specification" has been enhanced to allow for more flexible buffer management. This enhancement is fully backwards compatible.
All the new features are completely optional and do not collide with existing features. They may be used only when the protocol stack asks for them on opening a driver.
The enhancements consist of several new tags that may be specified by a protocol stack on OpenDevice() to offer certain data transfer options. It is up to the device driver to chose which callbacks to use at what time. These tags are advisory only and may be ignored by the driver for any data buffer at any time:
#define S2_CopyToBuff16 (S2_Dummy + 4) #define S2_CopyFromBuff16 (S2_Dummy + 5) #define S2_CopyToBuff32 (S2_Dummy + 6) #define S2_CopyFromBuff32 (S2_Dummy + 7)
These are optional callbacks presented to the device with the same calling interface as for S2_CopyToBuff or S2_CopyFromBuff, respectively. The difference to the original callbacks is the required and guaranteed transfer size and alignment for accessing the device's buffer for a single piece of a data of either 16 or 32 bits, a data word. The copy function called may only use 16/32 bit aligned read/write commands of 16/32 bits at once to transfer the data words, respectively. If the buffer data length is not a multiple of the required data word transfer size, the last data word transfer may contain garbage padding in either transfer direction.
The following tags have been added to support direct writes into hardware buffers that do not allow arbitrarily sized or aligned accesses:
#define S2_DMACopyToBuff32 (S2_Dummy + 8) #define S2_DMACopyFromBuff32 (S2_Dummy + 9)
If the protocol stack wants to optionally enhance data transfer efficiency with DMA supporting devices, it may pass any of these optional tags to the device on OpenDevice().
If the device driver supports DMA, it may call the respective callback with the abstract magic cookie ios2_Data in register A0. The callback may return NULL in D0. In this case, the driver may not use DMA for this buffer. Alternatively, the callback may return the address of the actual data buffer in D0, if it has these characteristics:
- The buffer is in contigous memory. Depending on the intended data direction, it shall be readable or writable.
- The buffer is aligned on a 32 bit boundary.
- The buffer size shall be a multiple of 32 bit and it is at least = ios2_DataLength.
- It is up to the driver to decide if it can use DMA for this buffer and it shall fall back to the standard CPU callbacks if necessary. The data transfer method actually used by the driver will not be known in advance by the protocol stack.
Packet Type
[packettypespage] Network frames always have a type field associated with them. These type fields vary in length, position and meaning by frame type (frame types generally correspond one-to-one with hardware types, but see "Ethernet Packet Types" below). The meanings of the type numbers are always carefully defined and every type number is registered with some official body. Do not use a type number which is not registered for any standard hardware you use or in a manner inconsistent with that registration.
The type field allows the SANA-II device driver to fulfill CMD_READs based on the type of packet the driver user wants. Multiple protocols can therefore run over the same wire using the same driver without stepping on each other's toes.
Packet types are specified as a long word. Unfortunately, the type field means different things on different wires. Driver users must allow their software to be configured with a SANA-II device name, unit number and the type number(s) used by the protocol stack with each device. This way, if new hardware becomes available, a hardware manufacturer can supply a listing of type assignments to configure pre-existing software.
Ethernet Packet Types
Ethernet has a special problem with packet types. Two types of ethernet frames can be sent over the same wire: ethernet and 802.3. These frames differ in that the Type field of an ethernet frame is the Length field of an 802.3 frame. This creates a problem in that demultiplexing incoming packets can be cumbersome and inefficient, as well as requiring driver users to be aware of the frame type used.
All 802.3 frames have numbers less than 1500 in the Type field. The only frames with numbers less than 1500 in the type field are 802.3 frames. SANA-II ethernet drivers abnormally return packets contained in ethernet frames when the requested Type falls within the 802.3 range-if the Type requested is within the 802.3 range, the driver returns the next packet contained within an 802.3 frame, regardless of the type specified for the packet within the 802.3 frame. This requires that there be no more than one driver user requesting 802.3 packets and that it do its own interpretation of the frames.
ARCNET Frames
ARCNET also has a special problem with framing. ARCNET frames consist of a hardware header and a software header. The software header is in the data area of the hardware packet, and includes at least the protocol ID.
There are two types of software header. Old-style ARCNET software headers consist entirely of a one or two byte protocol ID. New ARCNET software headers (defined in RFC 1201 and in the paper "ARCNET Packet Header Definition Standard", Novell, Inc., 1989) include more information. They allow more efficient use of ARCNET through data link layer fragmentation and reassembly (ARCNET has a small Maximum Transmission Unit) and allow sending any size packet up to the MTU (rather than requiring that packets of size 253, 254 and 255 be padded to at least 256 bytes).
SANA-II device drivers for ARCNET should implement the old ARCNET packet headers. Driver users which wish to interoperate with platforms using the new software headers must add the new fields to the data to be sent and must process it for incoming data. A SANA-II driver which implemented the data link layer fragmentation internally (and advertised a large MTU) could be more efficient than requiring the driver user to do it. This would make driver writing more difficult and reduce interoperability, but if there is ever a demand for that extra performance, a new hardware type may be assigned by Amiga for SANA-II ARCNET device drivers which implement the new framing.
Addressing
In the SANA-II standard, network hardware addresses are stored in an array of n bytes. No meaning is ascribed by the standard to the contents of the array.
In case there exists a network which does not have an address field consisting of a number of bits not divisible by eight, add pad bits at the end of the bit stream. For example, if an address is ten bits long it will be stored like this:
98765432 10PPPPPP BYTE 0 BYTE 1
Where the numerals are bit numbers and "P" is a pad (ignored) bit.
Driver users which do not implement the bit shifting necessary to use a network with such addressing (if one exists) should at least check the number of significant bits in the address field (returned from the device's S2_DEVICEQUERY function) to make sure that it is evenly divisible by eight.
Driver users will map hardware addresses to protocol addresses in a protocol and hardware dependent manner, as described by the relevant standards (i.e., RFC 826 for TCP/IP over Ethernet, RFC 1201 or RFC 1051 for TCP/IP over ARCNET). Some protocols will always use the same mapping on all hardware, but other protocols will have particular address mapping schemes for some particular hardware and a reasonable default for other (unknown) hardware.
Some SANA-II devices will have "hardware addresses" which aren't really hardware addresses. As an example, consider PPP (Point-to-Point Protocol). PPP is a standard for transmitting IP packets over a serial line. It uses IP addresses negotiated during the establishment of a connection. In a SANA-II driver implementation of PPP, the driver would negotiate the address at S2_CONFIGINTERFACE. Thus, the address in SrcAddr returned by the device on an S2_CONFIGINTERFACE (or in a subsequent S2_GETSTATIONADDRESS) will be a protocol address, not a true hardware address.
Note: Some hardware always uses a ROM hardware address. Other hardware which has a ROM address or is configurable with DIP switches may be overridden by software. Some hardware always dynamically allocates a new hardware address at initialization. See "Configuration" for details on how this is handled by driver writers and by driver users.
Hardware Type
The HardwareType returned by the device's S2_DEVICEQUERY function is necessary for those protocols whose standards require different behavior on different hardware. It is also useful for determining appropriate packet type numbers to use with the device. The HardwareType values already issued for standard network hardware are the same as those in RFC 1060 (assigned numbers). Hardware developers implementing networks without a SANA-II hardware number must contact the AmigaOS development team to have a new hardware type number assigned. Driver users should all have reasonable defaults which can be used for hardware with which they are not familiar.
Errors
The SANA-II extended IORequest structure (struct IOSana2Req) includes both the ios2_Error and ios2_WireError fields. Driver users must always check IOSana2Reqs on return for an error in ios2_Error. ios2_Error will be zero if no error occurred, otherwise it will contain a value from <exec/errors.h> or <devices/sana2.h>. If there was an error, there may be more specific information in ios2_WireError. Drivers are required to fill in the WireError if there is an applicable error code.
Error codes are #define'd in the "defined errors" sections of the file <devices/sana2.h>:
IOSana2Req S2io_Error field (S2ERR_xxx):
- S2ERR_NO_RESOURCES
- Insufficient resources available.
- S2ERR_BAD_ARGUMENT
- Noticeably bad argument.
- S2ERR_BAD_STATE
- Command inappropriate for current state.
- S2ERR_BAD_ADDRESS
- Noticeably bad address.
- S2ERR_MTU_EXCEEDED
- Write data too large.
- S2ERR_NOT_SUPPORTED
- Command is not supported by this driver. This is similar to IOERR_NOCMD as defined in <exec/errors.h> but S2ERR_NOT_SUPPORTED indicates that the requested command is a valid SANA-II command and that the driver does not support it because the hardware is incapable of supporting it (e.g., S2_MULTICAST). Note that IOERR_NOCMD is still valid for reasons other than a lack of hardware support (i.e., commands which are no-ops in a SANA-II driver).
- S2ERR_SOFTWARE
- Software error of some kind.
- S2ERR_OUTOFSERVICE
- When a hardware device is taken off-line, any pending requests are returned with this error.
See also the standard errors in <exec/errors.h>.
IOSana2Req S2io_WireError field (S2WERR_xxx):
- S2WERR_NOT_CONFIGURED
- Command requires unit to be configured.
- S2WERR_UNIT_ONLINE
- Command requires that the unit be off-line.
- S2WERR_UNIT_OFFLINE
- Command requires that the unit be on-line.
- S2WERR_ALREADY_TRACKED
- Protocol is already being tracked.
- S2WERR_NOT_TRACKED
- Protocol is not being tracked.
- S2WERR_BUFF_ERROR
- Buffer management function returned an error.
- S2WERR_SRC_ADDRESS
- Problem with the source address field.
- S2WERR_DST_ADDRESS
- Problem with destination address field.
- S2WERR_BAD_BROADCAST
- Problem with an attempt to broadcast.
- S2WERR_BAD_MULTICAST
- Problem with an attempt to multicast.
- S2WERR_MULTICAST_FULL
- Multicast address list full.
- S2WERR_BAD_EVENT
- Event specified is unknown.
- S2WERR_BAD_STATDATA
- The ios2_StatData pointer or the data it points to failed a sanity check.
- S2WERR_IS_CONFIGURED
- Attempt to reconfigure the unit.
- S2WERR_NULL_POINTER
- A NULL pointer was detected in one of the arguments. S2ERR_BAD_ARGUMENT should always be the S2ERR.
Standard Commands
See the "SANA-II network device driver Autodocs" for full details on each of the SANA-II device commands. Extended commands are explained in the sections below.
Many of the Exec device standard commands are no-ops in SANA-II devices, but this may not always be the case. For example, CMD_RESET might someday be used for dynamically reconfiguring hardware. This should present no compatibility problems for properly written drivers.
Broadcast and Multicast
Some hardware supports broadcast and/or multicast. A broadcast is a packet sent to all other machines. A multicast is a packet sent to a set of machines. Drivers for hardware which does not allow broadcast or multicast will return ios2_Error S2ERR_NOT_SUPPORTED as appropriate.
To send a broadcast, use S2_BROADCAST instead of CMD_WRITE. Broadcasts are received just like any other packets (using a CMD_READ for the appropriate packet type).
To send a multicast, use S2_MULTICAST instead of CMD_WRITE. The device keeps a list of addresses that want to receive multicasts. You add a receiver's address to this list by using S2_ADDMULTICASTADDRESS. The receiver then posts a CMD_READ for the type of packet to be received. Some SANA-II devices which support multicast may have a limit on the number of addresses that can simultaneously wait for packets. Always check for an S2WERR_MULTICAST_FULL error return when adding a multicast address.
Note that when the device adds a multicast address, it is usually added for all users of the device, not just the driver user which called S2_ADDMULTICASTADDRESS. In other words, received multicast packets will fill a read request of the appropriate type regardless of whether the requesting driver user is the same one which added the multicast address.
In general, driver users should not care how received packets were sent (normally or broadcast/multicast), only that it was received. If a driver user really must know, however, it can check for SANA2IOB_BCAST and/or SANA2IOB_MCAST in the ios2_Flags field.
Drivers should keep a count for the number of opens on a multicast address so that they don't actually remove it until it has been S2_DELMULTICASTADDRESS'd as many times as it has been S2_ADDMULTICASTADDRESS'd.
Stats
There are many statistics which may be very important to someone trying to debug, tune or optimize a protocol stack, as well as to the end user who may need to tune parameters or investigate a problem. Some of these statistics can only be kept by the SANA-II driver, thus there are several required and optional statistics and commands for this purpose.
S2_TRACKTYPE tells the device driver to gather statistics for a particular packet type. S2_UNTRACKTYPE tells it to stop (keeping statistics by type causes the driver to use additional resources). S2_GETTYPESTATS returns any statistics accumulated by the driver for a type being tracked (stats are lost when a type is S2_UNTRACKTYPE'd). Drivers are required to implement the functionality of type tracking. The stats are returned in a struct Sana2PacketTypeStats:
struct Sana2PacketTypeStats { ULONG PacketsSent; ULONG PacketsReceived; ULONG BytesSent; ULONG BytesReceived; ULONG PacketsDropped; };
- PacketsSent
- Number of packets of a particular type sent.
- PacketsReceived
- Number of packets of a particular type that satisfied a read command.
- BytesSent
- Number of bytes of data sent in packets of a particular type.
- BytesReceived
- Number of bytes of data of a particular packet type that satisfied a read command.
- PacketsDropped
- Number of packets of a particular type that were received while there were no pending reads of that packet type.
returns global statistics kept by the driver. Drivers are required to keep all applicable statistics. Since all are applicable to most hardware, most drivers will maintain all statistics. The stats are returned in a struct Sana2DeviceStats:
struct Sana2DeviceStats { ULONG PacketsReceived; ULONG PacketsSent; ULONG BadData; ULONG Overruns; ULONG UnknownTypesReceived; ULONG Reconfigurations; struct timeval LastStart; };
- PacketsReceived
- Number of packets that this unit has received.
- PacketsSent
- Number of packets that this unit has sent.
- BadData
- Number of bad packets received (i.e., hardware CRC failed).
- Overruns
- Number of packets dropped due to insufficient resources available in the network interface.
- UnknownTypeReceived
- Number of packets received that had no pending read command with the appropriate packet type.
- Reconfigurations
- Number of network reconfigurations since this unit was last configured.
- LastStart
- The time when this unit last went on-line.
returns any special statistics kept by a particular driver. Each new wire type will have a set of documented, required statistics for that wire type and a standard set of optional statistics for that wire type (optional because they might not be available from all hardware). The data returned by S2_GETSPECIALSTATS will require wire-specific interpretation. See <devices/sana2specialstats.h> on page devicessana2specialstatspage for currently defined special statistics. The statistics are returned in the following structures:
struct Sana2SpecialStatRecord { ULONG Type; ULONG Count; char * String; };
- Type
- Statistic identifier.
- Count
- Statistic itself.
- String
- An identifying, null-terminated string for the statistic. Should be plain ASCII with no formatting characters.
struct Sana2SpecialStatHeader { ULONG RecordCountMax; ULONG RecordCountSupplied; struct Sana2SpecialStatRecord[RecordCountMax]; };
- RecordCountMax
- There is space for this many records into which statistics may be placed.
- RecordCountSupplied
- Number of statistic records supplied.
is not, strictly speaking, a statistical function. It is a request to read any packet of a type for which there is no outstanding CMD_READ. S2_READORPHAN might be used in the same manner as many statistics, though, such as to determine what packet types are causing overruns, etc.
Configuration
The device driver needs to configure the hardware before using it. The driver user must know some network hardware parameters (hardware address and MTU, for example) when using it. These commands address those needs.
When a driver user is initialized, it should try to S2_CONFIGINTERFACE even though an interface can only be configured once and someone else may have done it. Before you call S2_CONFIGINTERFACE, first call S2_GETSTATIONADDRESS to determine the factory address (if any). Also provide for user-override of the factory address (that address may be optional and the user may need to override it). When S2_CONFIGINTERFACE returns, check the ios2_SrcAddr for the actual address the hardware has been configured with. This is because some hardware (or serial line standards such as PPP) always dynamically allocates an address at initialization.
Driver users will want to use S2_DEVICEQUERY to determine the MTU and other characteristics of the network. The structure returned from S2_DEVICEQUERY is defined as:
struct Sana2DeviceQuery { ULONG SizeAvailable; ULONG SizeSupplied; ULONG DevQueryFormat; ULONG DeviceLevel; ULONG AddrFieldSize; ULONG MTU; ULONG BPS; ULONG HardwareType; };
- SizeAvailable
- Size, in bytes, of the space available in which to place device information. This includes both size fields.
- SizeSupplied
- Size, in bytes, of the data supplied.
- DevQueryFormat
- The format defined here is format 0.
- DeviceLevel
- This spec defines level 0.
- AddrFieldSize
- The number of bits in an interface address.
- MTU
- Maximum Transmission Unit, the size, in bytes, of the maximum packet size, not including header and trailer information.
- BPS
- Best guess at the raw line rate for this network in bits per second.
- HardwareType
- Specifies the type of network hardware the driver controls.
On-line
In order to run hardware tests on an otherwise live system, the S2_OFFLINE command allows the SANA-II device driver to be "turned off" until the tests are complete and an S2_ONLINE is sent to the driver. S2_ONLINE causes the interface to re-configure and re-initialize. Any packets destined for the hardware while the device is off-line will be lost. All pending and new requests to the driver shall be returned with S2ERR_OUTOFSERVICE when a device is off-line.
All driver users must understand that any IO request may return with S2ERR_OUTOFSERVICE because the driver is off-line (any other program may call S2_OFFLINE to make it so). In such an event, the driver will usually want to wait until the unit comes back on-line (for the program which called S2_OFFLINE to call S2_ONLINE). It may do this by calling S2_ONEVENT to wait for S2EVENT_ONLINE. S2_ONEVENT allows the driver user to wait on various events.
A driver must track events, but may not distinguish between some types of events. Drivers return S2_ONEVENT with S2ERR_NOT_SUPPORTED and S2WERR_BAD_EVENT for unsupported events. One error may cause more than one event (see below). Errors which seem to have been caused by a malformed or unusual request should not generally trigger an event.
Event types (S2EVENT_xxx):
- S2EVENT_ERROR
- Return when any error occurs.
- S2EVENT_TX
- Return on any transmit error (always an error).
- S2EVENT_RX
- Return on any receive error (always an error).
- S2EVENT_ONLINE
- Return when unit goes on-line or return immediately if unit is already on-line (not an error).
- S2EVENT_OFFLINE
- Return when unit goes off-line or return immediately if unit is already off-line (not an error.)
- S2EVENT_BUFF
- Return on any buffer management function error (always an error).
- S2EVENT_HARDWARE
- Return when any hardware error occurs (always an error, may be a S2EVENT_TX or S2EVENT_RX, too).
- S2EVENT_SOFTWARE
- Return when any software error occurs (always an error, may be a S2EVENT_TX or S2EVENT_RX, too).
Driver Installation
The standard system location for SANA-II network device driver is in a directory called "Networks" which exists in the "DEVS:" directory.
Example:
DEVS:Networks/a2065.device
This is the official location for the drivers. It may be necessary for your install program/script to create this directory if it doesn't exist in a user's system.
Acknowledgments
Many people and companies have contributed to the "SANA-II Network Device Driver Specification". The original SANA-II Autodocs and includes were put together by Ray Brand, Perry Kivolowitz (ASDG) and Martin Hunt. Those original documents evolved to their current state and grew to include this document at the hands of Dale Larson and Greg Miller. Brian Jackson and John Orr provided valuable editing. Randell Jesup has provided sage advice on several occasions. The buffer management callback mechanism was his idea. Dale Luck (GfxBase) and Rick Spanbauer (Ameristar Technologies) have provided valuable comments throughout the process. Nicolas Benezan (ADONIS) provided many detailed and useful comments on weaknesses in late drafts of the specification. The enhancements for better buffer management, clarifications and notes for device implementers were added to the specification by Heinz Wrobel whilst consulting for Amiga Technologies GmbH, yielding revision 3.0 of the specification.
Thanks to all the above and the numerous others who have contributed with their comments, questions and discussions.
Unresolved Issues
Unfortunately, it isn't possible to completely isolate network protocols from the hardware they run on. Hardware types and addressing both remain somewhat hardware-dependent in spite of our efforts. See the "Packet Type" section for an explanation of how packet types are handled and why protocols cannot be isolated from them. See the "Addressing" section for an explanation of how addressing is handled any why protocols cannot be isolated from it.
Additionally, there are at least two cases where a hardware type has multiple framing methods in use (ethernet/802.3 and arcnet/(Novell) "ARCNET Packet Header Definition Standard"). In both cases, software which must interoperate with other platforms on this hardware may need to be aware of the distinctions and may have to do extra processing in order to use the appropriate frame type. See the sections on "Ethernet Packet Types" and on "ARCNET frames" for more details.
Another feature that SANA-II currently lacks is any concept of dynamic addressing. Some hardware types such as LocalTalk or dialup SLIP/PPP connections may change their address on the fly. Currently there is no way for a device driver to report this event back to a protocol stack.
SANA-II network device driver Autodocs
sana2.device/AbortIO
sana2.device/AbortIO sana2.device/AbortIO
NAME
AbortIO -- Remove an existing device request.
SYNOPSIS
error = AbortIO(Sana2Req)
D0 A1
LONG AbortIO(struct IOSana2Req *);
FUNCTION
This is an exec.library call.
This function aborts an ioRequest. If the request is active, it may or
may not be aborted. If the request is queued it is removed. The
request will be returned in the same way as if it had normally
completed. You must WaitIO() after AbortIO() for the request to
return.
INPUTS
Sana2Req - Sana2Req to be aborted.
RESULTS
error - Zero if the request was aborted, non-zero otherwise.
io_Error in Sana2Req will be set to IOERR_ABORTED
if it was aborted.
SEE ALSO
exec.library/AbortIO(), exec.library/WaitIO()
sana2.device/CloseDevice
sana2.device/CloseDevice sana2.device/CloseDevice
NAME
CloseDevice -- Close the device.
SYNOPSIS
CloseDevice(Sana2Req)
A1
void CloseDevice(struct IOSana2Req *);
FUNCTION
This function is called by exec.library CloseDevice().
This function performs whatever cleanup is required at device closes.
Note that all IORequests MUST be complete before closing. If any are
pending, your program must AbortIO() then WaitIO() each outstanding
IORequest to complete them.
INPUTS
Sana2Req - Pointer to IOSana2Req initialized by OpenDevice().
SEE ALSO
exec.library/CloseDevice(), exec.library/OpenDevice()
sana2.device/CMD_CLEAR
sana2.device/CMD_CLEAR sana2.device/CMD_CLEAR
NAME
Clear -- Clear internal network interface read buffers.
FUNCTION
There are no device internal buffers, so CMD_CLEAR does not apply to
this class of device.
IO REQUEST
ios2_Command - CMD_CLEAR.
RESULTS
ios2_Error - IOERR_NOCMD.
sana2.device/CMD_FLUSH
sana2.device/CMD_FLUSH sana2.device/CMD_FLUSH
NAME
Flush -- Clear all queued I/O requests for the SANA-II device.
FUNCTION
This command aborts all I/O requests in both the read and write
request queues of the device. All pending I/O requests are
returned with an error message (IOERR_ABORTED). CMD_FLUSH does not
affect active requests.
IO REQUEST
ios2_Command - CMD_FLUSH.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
sana2.device/CMD_INVALID
sana2.device/CMD_INVALID sana2.device/CMD_INVALID
NAME
Invalid -- Return with error IOERR_NOCMD.
FUNCTION
This command causes device driver to reply with an error IOERR_NOCMD
as defined in <exec/errors.h> indicating the command is not supported.
IO REQUEST
ios2_Command - CMD_INVALID.
RESULTS
ios2_Error - IOERR_NOCMD.
BUGS
Not known to be useful.
sana2.device/CMD_READ
sana2.device/CMD_READ sana2.device/CMD_READ
NAME
Read -- Get a packet from the network.
FUNCTION
Get the next packet available of the requested packet type. The data
copied (via a call to the requestor-provided CopyToBuffer function)
into ios2_Data is normally the Data Link Layer packet data only. If
bit SANA2IOB_RAW is set in ios2_Flags, then the entire physical frame
will be returned.
Unlike most Exec devices, SANA-II device drivers do not have internal
buffers. If you wish to read data from a SANA-II device you should
have multiple CMD_READ requests pending at any given time. The
functions provided by you the requestor will be used for any incoming
packets of the type you've requested. If no read requests are
outstanding for a type which comes in and no read_orphan requests are
outstanding, the packet will be lost.
IO REQUEST
ios2_Command - CMD_READ
ios2_Flags - Supported flags are:
SANA2IOB_RAW
SANA2IOB_QUICK
ios2_PacketType - Packet type desired.
ios2_Data - Abstract data structure to hold packet data.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
ios2_Flags - The following flags may be returned:
SANA2IOB_RAW
SANA2IOB_BCAST
SANA2IOB_MCAST
ios2_SrcAddr - Source interface address of packet.
ios2_DstAddr - Destination interface address of packet.
ios2_DataLength - Length of packet data.
ios2_Data - Abstract data structure which packet data is
contained in.
NOTES
The driver may not directly examine or modify anything pointed to by
ios2_Data. It *must* use the requester-provided functions to access
this data.
SEE ALSO
S2_READORPHAN, CMD_WRITE, any_protocol/CopyToBuffer
sana2.device/CMD_RESET
sana2.device/CMD_RESET sana2.device/CMD_RESET
NAME
Reset -- Reset the network interface to initialized state.
FUNCTION
Currently, SANA-II devices can only be configured once (with
CMD_CONFIGINTERFACE) and cannot be re-configured, hence,
CMD_RESET does not apply to this class of device.
IO REQUEST
ios2_Command - CMD_RESET.
RESULTS
ios2_Error - IOERR_NOCMD.
sana2.device/CMD_START
sana2.device/CMD_START sana2.device/CMD_START
NAME
Start -- Restart device operation.
FUNCTION
There is no way for the driver to keep queuing requests without
servicing them, so CMD_STOP does not apply to this class of device.
S2_OFFLINE and S2_ONLINE do perform a similar function to CMD_STOP
and CMD_START
IO REQUEST
ios2_Command - CMD_START.
RESULTS
ios2_Error - IOERR_NOCMD.
SEE ALSO
S2_ONLINE, S2_OFFLINE
sana2.device/CMD_STOP
sana2.device/CMD_STOP sana2.device/CMD_STOP
NAME
Stop -- Pause device operation.
FUNCTION
There is no way for the driver to keep queuing requests without
servicing them, so CMD_STOP does not apply to this class of device.
S2_OFFLINE and S2_ONLINE do perform a similar function to CMD_STOP
and CMD_START
IO REQUEST
ios2_Command - CMD_STOP.
RESULTS
ios2_Error - IOERR_NOCMD.
NOTES
SEE ALSO
S2_ONLINE, S2_OFFLINE
sana2.device/CMD_UPDATE
sana2.device/CMD_UPDATE sana2.device/CMD_UPDATE
NAME
Update -- Force packets out to device.
FUNCTION
Since there are no device internal buffers, CMD_UPDATE does not
apply to this class of device.
IO REQUEST
ios2_Command - CMD_UPDATE.
RESULTS
ios2_Error - IOERR_NOCMD.
sana2.device/CMD_WRITE
sana2.device/CMD_WRITE sana2.device/CMD_WRITE
NAME
Write -- Send packet to the network.
FUNCTION
This command causes the packet to be sent to the specified network
interface. Normally, appropriate packet header and trailer information
will be added to the packet data when it is sent. If bit SANA2IOB_RAW
is set in io_Flags, then the ios2_Data is assumed to contain an entire
physical frame and will be sent (copied to the wire via
CopyFromBuffer() unmodified.
Note that the device should not check to see if the destination
address is on the local hardware. Network protocols should realize
that the packet has a local destination long before it gets to a
SANA-II driver.
IO REQUEST
ios2_Command - CMD_WRITE.
ios2_Flags - Supported flags are:
SANA2IOB_RAW
SANA2IOB_QUICK
ios2_PacketType - Packet type to send.
ios2_DstAddr - Destination interface address for this packet.
ios2_DataLength - Length of the Data to be sent.
ios2_Data - Abstract data structure which packet data is
contained in.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
NOTES
The driver may not directly examine or modify anything pointed to by
ios2_Data. It *must* use the requester-provided functions to access
this data.
SEE ALSO
CMD_READ, S2_BROADCAST, S2_MULTICAST, any_protocol/CopyFromBuffer
sana2.device/OpenDevice
sana2.device/OpenDevice sana2.device/OpenDevice
NAME
Open -- Request an opening of the network device.
SYNOPSIS
error = OpenDevice(unit, IOSana2Req, flags)
D0 D0 A1 D1
BYTE OpenDevice(ULONG, struct IOSana2Req *, ULONG);
FUNCTION
This function is called by exec.library OpenDevice().
This function performs whatever initialization is required per
device open and initializes the Sana2Req for use by the
device.
INPUTS
unit - Device unit to open.
Sana2Req - Pointer to IOSana2Req structure to be initialized by
the sana2.device.
flags - Supported flags are:
SANA2OPB_MINE
SANA2OPB_PROM
ios2_BufferManagement - A pointer to a tag list containing
pointers to buffer management functions.
RESULTS
error - same as io_Error
io_Error - Zero if successful; non-zero otherwise.
io_Device - A pointer to whatever device will handle the calls
for this unit. This pointer may be different
depending on what unit is requested.
ios2_BufferManagement - A pointer to device internal information
used to call buffer management functions.
NOTES
A SANA-II device must reject all open requests with a request
structure that is too short, e.g. an IOStdReq. A simple check of the
mn_Length field in the Message part of the request is needed to make
sure that a device does not dereference invalid data due to a wrong
device configuration.
A SANA-II device may open if no buffer management tags are provided to
make the configuration process and obtaining statistics easier. Buffer
management tags with a NULL value must be treated as not specified.
The device shall fail requests gracefully depending on the missing
tags in this case. Any malfunction is not acceptable.
SEE ALSO
exec.library/OpenDevice(), exec.library/CloseDevice()
sana2.device/S2_ADDMULTICASTADDRESS
sana2.device/S2_ADDMULTICASTADDRESS sana2.device/S2_ADDMULTICASTADDRESS
NAME
AddMulticastAddress -- Enable an interface multicast address.
FUNCTION
This command causes the device driver to enable multicast packet
reception for the requested address.
IO REQUEST
ios2_Command - S2_ADDMULTICASTADDRESS.
ios2_SrcAddr - Multicast address to enable.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
NOTES
Multicast addresses are added globally -- anyone using the device
may receive packets as a result of any multicast address which has
been added for the device.
Since multicast addresses are not "bound" to a particular packet type,
each enabled multicast address has an "enabled" count associated with
it so that if two protocols add the same multicast address and later
one removes it, it is still enabled until the second removes it.
SEE ALSO
S2_MULTICAST, S2_DELMULTICASTADDRESS
sana2.device/S2_BROADCAST
sana2.device/S2_BROADCAST sana2.device/S2_BROADCAST
NAME
Broadcast -- Broadcast a packet on network.
FUNCTION
This command works the same as CMD_WRITE except that it also performs
whatever special processing of the packet is required to do a
broadcast send. The actual broadcast mechanism is neccessarily
network/interface/device specific.
IO REQUEST
ios2_Command - S2_BROADCAST.
ios2_Flags - Supported flags are:
SANA2IOB_RAW
SANA2IOB_QUICK
ios2_PacketType - Packet type to send.
ios2_DataLength - Length of the Data to be sent.
ios2_Data - Abstract data structure which packet data is
contained in.
RESULTS
ios2_DstAddr - The contents of this field are to be
considered trash upon return of the IOReq.
ios2_Error - Zero if successful; non-zero otherwise.
This command can fail for many reasons and
is not supported by all networks and/or
network interfaces.
ios2_WireError - More specific error number.
NOTES
The DstAddr field may be trashed by the driver because this function
may be implemented by filling DstAddr with a broadcast address and
internally calling CMD_WRITE.
SEE ALSO
CMD_WRITE, S2_MULTICAST
sana2.device/S2_CONFIGINTERFACE
sana2.device/S2_CONFIGINTERFACE sana2.device/S2_CONFIGINTERFACE
NAME
ConfigInterface -- Configure the network interface.
FUNCTION
This command causes the device driver to initialize the interface
hardware and to set the network interface address to the address in
ios2_SrcAddr. This command can only be executed once and, if
successful, will leave the driver and network interface fully
operational and the network interface in ios2_SrcAddr.
To set the interface address to the factory address, the network
management software must use GetStationAddress first and then call
ConfigInterface with the result. If there is no factory address then
the network software must pick an address to use.
Until this command is executed the device will not listen for any
packets on the hardware.
IO REQUEST
ios2_Command - S2_CONFIGINTERFACE.
ios2_Flags - Supported flags are:
SANA2IOB_QUICK
ios2_SrcAddr - Address for this interface.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
ios2_SrcAddr - Address of this interface as configured.
NOTES
Some networks have the interfaces choose a currently unused interface
address each time the interface is initialized. The caller must check
ios2_SrcAddr for the actual interface address after configuring the
interface.
SEE ALSO
S2_GETSTATIONADDRESS
sana2.device/S2_DELMULTICASTADDRESS
sana2.device/S2_DELMULTICASTADDRESS sana2.device/S2_DELMULTICASTADDRESS
NAME
DelMultiCastAddress -- Disable an interface multicast address.
FUNCTION
This command causes device driver to disable multicast packet
reception for the requested address.
It is an error to disable a multicast address that is not enabled.
IO REQUEST
ios2_Command - S2_DELMULTICASTADDRESS
ios2_SrcAddr - Multicast address to disable.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
NOTES
Multicast addresses are added globally -- anyone using the device
may receive packets as a result of any multicast address which has
been added for the device.
Since multicast addresses are not "bound" to a particular packet type,
each enabled multicast address has an "enabled" count associated with
it so that if two protocols add the same multicast address and later
one removes it, it is still enabled until the second removes it.
SEE ALSO
S2_ADDMULTICASTADDRESS
sana2.device/S2_DEVICEQUERY
sana2.device/S2_DEVICEQUERY sana2.device/S2_DEVICEQUERY
NAME
DeviceQuery -- Return parameters for this network interface.
FUNCTION
This command causes the device driver to report information about the
device. Up to SizeAvailable bytes of the information is copied
into a buffer pointed to by ios2_StatData. The format of the data is
as follows:
struct Sana2DeviceQuery
{
/*
** Standard information
*/
ULONG SizeAvailble; /* bytes available */
ULONG SizeSupplied; /* bytes supplied */
LONG DevQueryFormat; /* this is type 0 */
LONG DeviceLevel; /* this document is level 0 */
/*
** Common information
*/
UWORD AddrFieldSize; /* address size in bits */
ULONG MTU; /* maximum packet data size */
LONG bps; /* line rate (bits/sec) */
LONG HardwareType; /* what the wire is */
/*
** Format specific information
*/
};
The SizeAvailable specifies the number of bytes that the caller
is prepared to accomodate, including the standard information fields.
SizeSupplied is the number of bytes actually supplied,
including the standard information fields, which will not exceed
SizeAvailable.
<devices/sana2.h> includes constants for these values. If your
hardware does not have a number assigned to it, you must contact
the AmigaOS development team to get a hardware number.
IO REQUEST
ios2_Command - S2_DEVICEQUERY.
ios2_StatData - Pointer to Sana2DeviceQuery structure to fill in.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
sana2.device/S2_GETGLOBALSTATS
sana2.device/S2_GETGLOBALSTATS sana2.device/S2_GETGLOBALSTATS
NAME
GetGlobalStats -- Get interface accumulated statistics.
FUNCTION
This command causes the device driver to retrieve various global
runtime statistics for this network interface. The format of the
data returned is as follows:
struct Sana2DeviceStats
{
ULONG PacketsReceived;
ULONG PacketsSent;
ULONG BadData;
ULONG Overruns;
ULONG UnknownTypesReceived;
ULONG Reconfigurations;
timeval LastStart;
};
IO REQUEST
ios2_Command - S2_GETGLOBALSTATS.
ios2_StatData - Pointer to Sana2DeviceStats structure to fill.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
SEE ALSO
S2_GETSPECIALSTATS
sana2.device/S2_GETSPECIALSTATS
sana2.device/S2_GETSPECIALSTATS sana2.device/S2_GETSPECIALSTATS
NAME
GetSpecialStats -- Get network type specific statistics.
FUNCTION
This function returns statistics which are specific to the type of
network medium this driver controls. For example, this command could
return statistics common to all Ethernets which are not common to all
network mediums in general.
The supplied Sana2SpecialStatData structure is given below:
struct Sana2SpecialStatData
{
ULONG RecordCountMax;
ULONG RecordCountSupplied;
struct Sana2StatRecord[RecordCountMax];
};
The format of the data returned is:
struct Sana2StatRecord
{
ULONG Type; /* Amiga registered */
LONG Count; /* the stat itself */
char *String; /* null terminated */
};
The RecordCountMax field specifies the number of records that the
caller is prepared to accomodate.
RecordCountSupplied is the number of record actually supplied which
will not exceed RecordCountMax.
IO REQUEST
ios2_Command - S2_GETSPECIALSTATS.
ios2_StatData - Pointer to a Sana2SpecialStatData structure to fill.
RecordCountMax must be initialized.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
NOTES
Amiga will maintain registered statistic Types.
SEE ALSO
S2_GETGLOBALSTATS, <devices/sana2specialstats.h>
sana2.device/S2_GETSTATIONADDRESS
sana2.device/S2_GETSTATIONADDRESS sana2.device/S2_GETSTATIONADDRESS
NAME
GetStationAddress -- Get default and interface address.
FUNCTION
This command causes the device driver to copy the current interface
address into ios2_SrcAddr, and to copy the factory default station
address (if any) into ios2_DstAddr.
IO REQUEST
ios2_Command - S2_GETSTATIONADDRESS.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
ios2_SrcAddr - Current interface address.
ios2_DstAddr - Default interface address (if any).
SEE ALSO
S2_CONFIGINTERFACE
sana2.device/S2_GETTYPESTATS
sana2.device/S2_GETTYPESTATS sana2.device/S2_GETTYPESTATS
NAME
GetTypeStats -- Get accumulated type specific statistics.
FUNCTION
This command causes the device driver to retrieve various packet type
specific runtime statistics for this network interface. The format of
the data returned is as follows:
struct Sana2TypeStatData
{
LONG PacketsSent;
LONG PacketsReceived;
LONG BytesSent;
LONG BytesReceived;
LONG PacketsDropped;
};
IO REQUEST
ios2_Command - S2_GETTYPESTATS.
ios2_PacketType - Packet type of interest.
ios2_StatData - Pointer to TypeStatData structure to fill in.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
NOTES
Statistics for a particular packet type are only available while that
packet type is being ``tracked''.
SEE ALSO
S2_TRACKTYPE, S2_UNTRACKTYPE
sana2.device/S2_MULTICAST
sana2.device/S2_MULTICAST sana2.device/S2_MULTICAST
NAME
Multicast -- Multicast a packet on network.
FUNCTION
This command works the same as CMD_WRITE except that it also performs
whatever special processing of the packet is required to do a
multicast send. The actual multicast mechanism is neccessarily
network/interface/device specific.
IO REQUEST
ios2_Command - S2_MULTICAST.
ios2_Flags - Supported flags are:
SANA2IOB_RAW
SANA2IOB_QUICK
ios2_PacketType - Packet type to send.
ios2_DstAddr - Destination interface address for this packet.
ios2_DataLength - Length of the Data to be sent.
ios2_Data - Abstract data structure which packet data is
contained in.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
This command can fail for many reasons and
is not supported by all networks and/or
network interfaces.
ios2_WireError - More specific error number.
NOTES
The address supplied in ios2_DstAddr will be sanity checked (if
possible) by the driver. If the supplied address fails this sanity
check, the multicast request will fail immediately with ios2_Error
set to S2WERR_BAD_MULTICAST.
Another Amiga will not receive a multicast packet unless it has had
the particular multicast address being used S2_ADDMULTICASTADRESS'd.
SEE ALSO
CMD_WRITE, S2_BROADCAST, S2_ADDMULTICASTADDRESS
sana2.device/S2_OFFLINE
sana2.device/S2_OFFLINE sana2.device/S2_OFFLINE
NAME
Offline -- Remove interface from service.
FUNCTION
This command removes a network interface from service.
IO REQUEST
ios2_Command - S2_OFFLINE.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
NOTES
Aborts all pending reads and writes with ios2_Error set to
S2ERR_OUTOFSERVICE.
While the interface is offline, all read, writes and any other
command that touches interface hardware will be rejected with
ios2_Error set to S2ERR_OUTOFSERVICE.
This command is intended to permit a network interface to be
tested on an otherwise live system.
SEE ALSO
S2_ONLINE
sana2.device/S2_ONEVENT
sana2.device/S2_ONEVENT sana2.device/S2_ONEVENT
NAME
OnEvent -- Return when specified event occures.
FUNCTION
This command returns when a particular event condition has occured
on the network or this network interface.
IO REQUEST
ios2_Command - S2_ONEVENT.
ios2_Flags - Supported flags are:
SANA2IOB_QUICK
ios2_WireError - Mask of event(s) to wait for
(from <devices/sana2.h>).
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - Mask of events that occured.
NOTES
If this device driver does not understand the specified event
condition(s) then the command returns immediately with
ios2_Req.io_Error set to S2_ERR_NOT_SUPPORTED and ios2_WireError
S2WERR_BAD_EVENT. A successful return will have ios2_Error set to
zero ios2_WireError set to the event number.
All pending requests for a particular event will be returned when
that event occurs.
All event types that cover a particular condition are returned when
that condition occures. For instance, if an error is returned by
a buffer management function during receive processing, events of
types S2EVENT_ERROR, S2EVENT_RX and S2EVENT_BUFF would be returned if
pending.
Types ONLINE and OFFLINE return immediately if the device is
already in the state to be waited for.
sana2.device/S2_ONLINE
sana2.device/S2_ONLINE sana2.device/S2_ONLINE
NAME
Online -- Put a network interface back in service.
FUNCTION
This command places an offline network interface back into service.
IO REQUEST
ios2_Command - S2_ONLINE.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
NOTES
This command is responsible for putting the network interface
hardware back into a known state (as close as possible to the
state before S2_OFFLINE) and resets the unit global and special
statistics.
SEE ALSO
S2_OFFLINE
sana2.device/S2_READORPHAN
sana2.device/S2_READORPHAN sana2.device/S2_READORPHAN
NAME
ReadOrphan -- Get a packet for which there is no reader.
FUNCTION
Get the next packet available that does not satisfy any then-pending
CMD_READ requests. The data returned in the ios2_Data structure is
normally the Data Link Layer packet type field and the packet data. If
bit SANA2IOB_RAW is set in ios2_Flags, then the entire Data Link Layer
packet, including both header and trailer information, will be
returned.
IO REQUEST
ios2_Command - CMD_READORPHAN.
ios2_Flags - Supported flags are:
SANA2IOB_RAW
SANA2IOB_QUICK
ios2_DataLength - Length of the Data to be sent.
ios2_Data - Abstract data structure which packet data is
contained in.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
ios2_Flags - The following flags may be returned:
SANA2IOB_RAW
SANA2IOB_BCAST
SANA2IOB_MCAST
ios2_SrcAddr - Source interface address of packet.
ios2_DstAddr - Destination interface address of packet.
ios2_DataLength - Length of the Data to be sent.
ios2_Data - Abstract data structure which packet data is
contained in.
NOTES
This is intended for debugging and management tools. Protocols should
not use this.
As with 802.3 packets on an ethernet, to determine which protocol
family the returned packet belongs to you may have to specify
SANA2IOB_RAW to get the entire data link layer wrapper (which is where
the protocol type may be kept). Notice this necessarily means that
this cannot be done in a network interface independent fashion. The
driver will, however, fill in the PacketType field to the best of its
ability.
SEE ALSO
CMD_READ, CMD_WRITE
sana2.device/S2_TRACKTYPE
sana2.device/S2_TRACKTYPE sana2.device/S2_TRACKTYPE
NAME
TrackType -- Accumulate statistics about a packet type.
FUNCTION
This command causes the device driver to accumulate statistics about
a particular packet type. Packet type statistics, for the particular
packet type, are zeroed by this command.
IO REQUEST
ios2_Command - S2_TRACKTYPE.
ios2_PacketType - Packet type of interest.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
SEE ALSO
S2_UNTRACKTYPE, S2_GETTYPESTATS
sana2.device/S2_UNTRACKTYPE
sana2.device/S2_UNTRACKTYPE sana2.device/S2_UNTRACKTYPE
NAME
UntrackType -- End statistics about a packet type.
FUNCTION
This command causes the device driver to stop accumulating
statistics about a particular packet type.
IO REQUEST
ios2_Command - S2_UNTRACKTYPE.
ios2_PacketType - Packet type of interest.
RESULTS
ios2_Error - Zero if successful; non-zero otherwise.
ios2_WireError - More specific error number.
SEE ALSO
S2_TRACKTYPE, S2_GETTYPESTATS
Callback mechanism Autodocs
CopyFromBuff
CopyFromBuff CopyFromBuff
NAME
CopyFromBuff -- Copy n bytes from an abstract data structure.
SYNOPSIS
success = CopyFromBuff(to, from, n)
d0 a0 a1 d0
BOOL CopyToBuff(VOID *, VOID *, ULONG);
FUNCTION
This function copies 'n' bytes of data in the abstract data structure
pointed to by 'from' into the contigous memory pointed to by 'to'.
'to' must contain at least 'n' bytes of usable memory or innocent
memory will be overwritten.
INPUTS
to - pointer to contiguous memory to copy to.
from - pointer to abstract structure to copy from.
n - number of bytes to copy.
RESULT
success - TRUE if operation was successful, else FALSE.
NOTES
This function must be callable from interrupts. In particular, this
means that this function may not directly or indirectly call any
system memory functions (since those functions rely on Forbid() to
protect themselves) and that you must not compile this function
with stack checking enabled. See the Exec Interrupts
chapter for more details on what is legal in a routine called from
an interrupt handler.
'C' programmers should not compile with stack checking (option '-v'
in SAS) and should geta4() or __saveds.
CopyToBuff
CopyToBuff CopyToBuff
NAME
CopyToBuff -- Copy n bytes to an abstract data structure.
SYNOPSIS
success = CopyToBuff(to, from, n)
d0 a0 a1 d0
BOOL CopyToBuff(VOID *, VOID *, ULONG);
FUNCTION
This function first does any initialization and/or allocation
required to prepare the abstract data structure pointed at by 'to'
to be filled with 'n' bytes of data from 'from'. It then executes
the copy operation.
If, for example, there is not enough memory available to prepare
the abstract data structure, the call is failed and FALSE is returned.
The buffer management scheme should be such that any memory needed
to fulfill CopyToBuff() calls is already allocated from the system
before the call to CopyToBuff() is made.
INPUTS
to - pointer to abstract structure to copy to.
from - pointer to contiguous memory to copy from.
n - number of bytes to copy.
RESULT
success - TRUE if operation was successful, else FALSE.
NOTES
This function must be callable from interrupts. In particular, this
means that this function may not directly or indirectly call any
system memory functions (since those functions rely on Forbid() to
protect themselves) and that you must not compile this function
with stack checking enabled. See the Exec Interrupts
chapter for more details on what is legal in a routine called from
an interrupt handler.
'C' programmers should not compile with stack checking (option '-v'
in SAS) and should geta4() or __saveds.
PacketFilter
PacketFilter PacketFilter
NAME
PacketFilter -- Perform filtering operation on CMD_READ's.
SYNOPSIS
keep = PacketFilter(hook, ios2, data)
d0 a0 a2 a1
BOOL PacketFilter(struct Hook *, struct IOSana2Req *, APTR);
FUNCTION
This function (if supplied by a protocol stack) may be used to
reject packets before they are copied into a protocol stack's
internal buffers.
The IOSana2Req structure should be set up to look (almost) exactly
as it would if it was successfully returned for the current packet.
Specifically, the fields that should be set up correctly are:
ios2->ios2_DataLength
ios2->ios2_SrcAddr
ios2->ios2_DstAddr
The "data" pointer must point to the beginning of the packet data
that is stored in contiguous memory. The data should NOT include
any hardware specific headers (unless of course the CMD_READ
request wanted RAW packets).
INPUTS
hook - pointer to the Hook originally supplied during
OpenDevice().
ios2 - The IOSana2Req CMD_READ request that will be used
(the "object" of the Hook call).
data - The packet data (the "message" of the Hook call).
RESULT
success - TRUE if the driver should provide the packet to
the protocol stack, FALSE if the packet should be
ignored.
NOTES
This function must be callable from interrupts. In particular, this
means that this function may not directly or indirectly call any
system memory functions (since those functions rely on Forbid() to
protect themselves) and that you must not compile this function
with stack checking enabled. See the Exec Interrupts
chapter for more details on what is legal in a routine called from
an interrupt handler.
'C' programmers should not compile with stack checking (option '-v'
in SAS) and should geta4() or __saveds.
What does packet filtering do? With the original ``SANA-II Network
Device Driver Specification'', a protocol stack could open a device
and ask for certain packet types. It got all the packets that matched
this type. As it turned out, this could be mighty inefficient if there
were packets that the protocol stack did not use at all. These would
go into read processing of the protocol stack and waste CPU time even
though they could have been easily identified on arrival.
Ethernet description
#define S2WireType_Ethernet 1
ios2_DataLength:
valid ethernet packets have 64 to 1500 bytes of data.
Address format:
Ethernet addresses consist of 47 bits of address information and
a 1 bit multicast flag. The standard for expressing ethernet
addresses is as 6 bytes (octets) in the order in which the bytes
are transmitted with the low-order bits in a byte transmitted
first. The multicast flag bit is the least-significant bit of the
first byte.
Ethernet addresses in a Sana2IOReq occupy the first 6 bytes of
an address field in transmission order with the low-order bits in
a byte transmitted first.
Station Address:
Each ethernet board must have a unique ethernet hardware address.
Drivers will override any attempt to set the address to anything
other than the ROM address.
Raw reads and writes:
6 bytes of destination address,
6 bytes of source address,
2 bytes of type,
64 to 1500 bytes of data
(followed by 4 byte CRC value covering all of the above
which is hardware generated and checked, hence not included
in even raw packets)
Multicast: Supported
Broadcast: Supported
Promiscuous: Supported
Packet Type Numbers for Ethernet are assigned by:
Xerox Corporation
Xerox Systems Institute
475 Oakmead Parkway, Sunnyvale, CA 94086
Attn: Ms. Fonda Pallone
(408) 737-4652
Some Common Packet Type Numbers:
decimal Hex Description
------- --- -----------
000 0000-05DC IEEE 802.3 Length Field
2048 0800 TCP/IP -- IP
2054 0806 TCP/IP -- ARP
32821 8035 TCP/IP -- RARP
32923 809B Appletalk
33011 80F3 AppleTalk AARP (Kinetics)
33100 814C SNMP
33079 8137-8138 Novell, Inc.
ARCNET description
S2WireType_Arcnet 7
ios2_DataLength:
506 byte MTU (because of the possibility of two byte Types).
Packets of size 254, 255, or 256 bytes are padded to 257 bytes before
transmition.
Station Address:
ARCNET hardware may have addresses set with jumpers, DIP switches
or software. Different drivers may therefore behave differently
with S2_CONFIGINTERFACE.
Hardware addresses should be assigned by users from highest to lowest
because there is some efficiency gained in the token passing scheme
this way. For example, on a three node network, hardware numbers 254,
253 and 252 should be used rather than 1, 2 and 3.
Raw reads and writes:
Short Packets (1-253 bytes)
Destination Address (1 byte)
Source Address (1 byte)
Count (256-N-Type length) (1 byte)
Padding (to byte number Count)
Type (1 or 2 bytes)
Data (N bytes)
Long Packets (257-506 bytes)
Destination Address (1 byte)
Source Address (1 byte)
zero (1 byte)
Count (512-N-Type length) (1 byte)
Padding (to byte number Count)
Type (1 or 2 bytes)
Data (N bytes)
Multicast: Not Supported
Broadcast: Supported
Promiscuous: Generally Not Supported
Packet Type Numbers for ARCNET are assigned by:
Datapoint Corporation
Some Common Packet Type Numbers
decimal hex description
------- --- -----------
221 DD AppleTalk
240 F0 TCP/IP -- IP (RFC 1051)
241 F1 TCP/IP -- ARP (RFC 1051)
212 F0 TCP/IP IP (RFC 1201, proposed)
213 F1 TCP/IP -- ARP (RFC 1201, proposed)
214 D6 TCP/IP -- RARP (RFC 1201, proposed)
247 F7 Banyan Vines
250 FA Novell IPX
